Dvb-T Senderliste Nrw

today the official "beta phase" des DVB-T2 broadcast has actually started in Germany. Till now, it was only possible zu receive DVB-T2 channels in certain areas (now ns area ist much more wider).

Du schaust: Dvb-t senderliste nrw

I would like to provide a quick howto weil das those who seeking assistance on this topic. I in using webocalendar.com ~ above a Raspberry-PI1 B+. Together receivers ich use 2 DVB-T2 USB rod "August T210".

Retrieving the frequency number¶

Take a look at here zum a list von DVB-T2 stations: http://www.dvb-t2hd.de/files/Senderstandorte_Erste_Stufe_DVB-T2_HD.pdfHere is a list des DVB-T stations: https://de.wikipedia.org/wiki/Liste_der_DVB-T-Sender_in_Deutschland

Here in my region NRW, there are number of stations, yet all use die same channel 43. Now, unfortunately ich was notfall able kommen sie find a table listing "unassigned" channels. Therefore i just calculated ns channel frequency. Each dvb-t channel has a bandwidth des 8Mhz. Acquisition channel number 45, which has a frequency of 666MHz (muahaha) you nur need zu subtract (2x8MHz) kommen sie get ns frequency zum channel 43 => 650MHz (Wow, that"s prefer rocket science).

Setting nach oben channel in webocalendar.com¶

Now, us need kommen sie setup this neu found mux in our webocalendar.com configuration. I have created a neu network called DVB-T2 for this purpose und assigned it zu my both receiver.

Afterwards, i created manually a neu mux with ns following data:

frequency (Hz): 650000000 Bandwidth: 8Mhz Constellation: QAM/AUTO delivery System: DVBT2I left any type of other value über default (or AUTO). Ich went rückseitig to Networks and selected the new network "DVB-T2" and clicked on "Force Scan". Ich was able kommen sie see in the log window, that webocalendar.com was able kommen sie find 6 new services. Ns two service "ARD HD" and "ZDF HD" might be mapped as new channels.

-> die other RTL, ProSieben, SAT.1, VOX could not be accessed über webocalendar.com. Ns reason is clear, die are encrypted.

Even though, ARD and ZDF are marked as encrypted von webocalendar.com, i was able kommen sie stream them on my android mobile.

Streaming results¶

As already mentioned in the ar above, i was able zu stream ns two unencrypted channels ARD und ZDF v my android mobile - however only through a few drawbacks.

the bild was there, yet no sound. MX Player was complaining about notfall supported audio currently (EAC3)

only the zuerst few frames of the stream were visible. Afterwards, ns picture gott stuck. Die sound was ok!

Linux Mint v Kodi 16.1:¶

no foto no sound. Ich guess i need to install die HEVC codec (H.265)

So much these room my zuerst experiences with DVB-T2. If anyone else has actually other experiences, or kann sein report effective streams, feeling free to report it here :-).

Michael


*
RE: Howto: Setup german DVB-T2 "beta" channels-Added by Michael Freudenberg end 5 years ago
*
RE: Howto: Setup german DVB-T2 "beta" channels-Added von Bengt Madeberg end 5 year ago
*
RE: Howto: Setup german DVB-T2 "beta" channels-Added von Michael Freudenberg over 5 year ago

Test with kodi (former xbmc) it supports HEVC.

I did the (last bolder paragraph bei the anfangsverdacht post). Ich was notfall able zu watch direkte TV respectively zu stream via the official webocalendar.com HTSP plugin for kodi.

Mehr sehen: Argumente Für Und Gegen Brexit Referendum, Nach Dem Brexit

BUT, ich recorded a show und was able zu watch this show in HD v no bild or sound problems. I know the kodi support HEVC since version 14 (http://kodi.wiki/view/HEVC). Still, ich saw that watching die recorded HD show required a gewächs of cpu ressources top top my core i5 laptop. I opened my job manager bei parallel und monitored die cpu load rising up to 70-80%.

Its seems weil das me to be in issue with the HTSP plugin zum Kodi. I posted a new thread on the kodi forum (http://forum.kodi.tv/showthread.php?tid=278293). Ich already wrote an answer zu this thread right here (http://forum.kodi.tv/showthread.php?tid=261370), yet no one is responding. Perhaps because ns title claims "solved" :-).


*
RE: Howto: Setup german DVB-T2 "beta" channels-Added von Michael Freudenberg end 5 year ago
*
RE: Howto: Setup german DVB-T2 "beta" channels-Added von Michael Freudenberg over 5 years ago

Good news,

I was able kommen sie compile und install the latest webocalendar.com version from git source. Die result is -> I tun können now watch both german DVB-T2 HD channels! Hooray!

BUT, the picture ist not yes, really smooth. Meaning, ns stream zu sein played back slower than die audio. Because of this after a few seconds die picture zu sein out von sync through audio. I assume this has kommen sie do with the HEVC coded und the compelled performance zum viewing it. I guess mine Lenovo X201 does notfall support DXVA or any kind of other HW encoding von HEVC.

Here are ns details:

Server:raspberry PI B+webocalendar.com git-version 4.1-2135

Client:Lenovo X201 windows 10 v Kodi 16.1 jarvis


I in reality made some procedures forward in my research: i found a list von Linux supported DVB-T2 devices: https://www.linuxtv.org/wiki/index.php/DVB-T2_USB_DevicesEven though ns one i found seems to be supported, it appears only ns DVB-T is supported.

I then found ns Geniatech T230 on a geschäft here http://de.aliexpress.com/store/product/dvb-t2-receiver-GENIATECH-Mygica-USB-TV-Stick-T230-DVB-T2-Tuner-DVB-C-DVB-T/616485_1883597971.html weil das 20€ und I was wondering if some of you oase experience v it and think it"s a good idea kommen sie give it a shot with my Raspberry PI und webocalendar.com


lord slash wrote:

Hi! i m sorry DVB-T2 pole receiver did you use? ich found this <> and I was wondering if it"s possible to connect it through a Raspberry PI 2 und webocalendar.com. Do freundin know something around it?

I have the rebadged Geniatech T230 (August T210v2) und have previously provided it on ns Pi without issue. I also have the Astrometa (the zuerst version v the schwarz strip), correctly it does arbeiten but the driver I"ve discovered has a couple of issues (causes tvh kommen sie use a silly amount of cpu). I"d go with the Silabs based tuner (the Geniatech) if i were you, viel better driver, punkt least on the Pi still (I"ve found).


Hi,

I in using two august DVB-T210 Sticks

https://www.amazon.de/August-DVB-T210-Videorecorder-Fernbedienung-kompatibel/dp/B008D8K50Q/ref=sr_1_1?ie=UTF8&qid=1472044533&sr=8-1&keywords=august+dvb-t210

Both work really great with mine webocalendar.com 4.1 (compiled indigenous git). I am using a raspberry 1 B+. Die CPU load is quite moderate for one stream (20%-30% no matter if DVB-T or DVB-T2).I am planning zu migrate ~ above a raspbery pi 2. Ich guess this would be the better platform, because it has much more cpu power und therefore kann sein handle an ext streaming clients.

Setting hoch the august T210 rod is deshalb easy. You only need download ns firmware und copy it to /lib/firmware


I use two, because ich like zu record a gewächs of series. Zu prevent a conflict wie man recordings are booked on two different channels in parallel, you need two or much more receiver. Of course, if two networks are on die same "mux" - only one receiver möchte be inhabited (i tested that). This also applies, wie you want kommen sie watch direkte tv und record an parallel.

Regarding the github build. Ich tried the town hall the new german HD channels, which are encoded in H.265/HEVC. Ich had issues with kodi 16.1 and the webocalendar.com plugin, wie streaming from webocalendar.com version 4.09. After i installed the github build i could stream HEVC encoded HD channels from kodi (presuming a HEVC capable client). Right jetzt i have webocalendar.com 4.1-2135 installed, and i tun können watch die HD channels on my desktop PC (AMD FX8230) and in Odroid-C2 through Librelec. Zum instance, it"s not working "seamless" on mine Lenovo X201, which ist to old to assistance HEVC über the incorporated Intel graphics, and seemingly not in der nähe des enough zu process it via software encoding (tried this top top kodi 16.1 und Windows 10).


Hi! ich finally managed to get my Geniatech T230C zu work through my Raspbian und webocalendar.com (I so compiled die 4.1-2247). It functions perfectly with die DVB-T channels, but as soon as i add die DVB-T2 Mux together explained in this subject the scan fails. Here zu sein what i did:I oase created a new network named DVB-T2 for this purpose und assigned it kommen sie my both receiver.Afterwards, ich created manually a new mux with die following data:frequency (Hz): 650000000Bandwidth: 8MhzConstellation: QAM/AUTODelivery System: DVBT2I left any type of other value von default (or AUTO). I went back to Networks und selected the new network "DVB-T2" and clicked on "Force Scan".

Mehr sehen: Archiv: Lotto Samstag 16.05 20, Lottoziehung Samstag 16

any idea if there ist some other parameter that i might have forgotten?


Turned the end that ns right frequency weil das DVB-T2 HD channels was 642MHz instead des 650MHz. I in wondering if the frequency is different depending on the city.. Anyway ich cannot watch ns HD channels on my PI yet:

when i stream bei HD channel on webocalendar.com from my DVB-T2 stick the CPU goes kommen sie 100% und the videobilien gets really jerky and unwatchable (SD channels arbeiten fine). More in detail ns setup that i have:- Raspberry Pi 2 v Raspbian Jessie, kernel 4.4.21-v7+- Backend ist webocalendar.com 4.1-2247 (github build)- DVB-T2 Stick is a Geniatech T230C (newer version des the T230, so known as ehrenvoll T210, driver Silicon Labs Si2168 compiled indigenous here: https://bitbucket.org/CrazyCat/media_build )- Kodi 16.1 (github build): MPG2 and WVC1 codecs purchased and enabled; /boot/config.txt consists of gpu_mem=256; video hardware acceleration MMAL enabled;- PVR Frontend zu sein webocalendar.com HTSP customer 2.2.12

When ich select an SD channel it functions perfectly, when i select in HD channel die CPU walk quicky kommen sie 100% und I can"t watch ns channel. When ich watch ns HD channel ~ above my fenster computer through VLC it functions flawlessy (so i guess my belästigung is not with die backend however with ns frontend/kodi)I möchte attach a Kodi log in file and a screenshotWhat am I act wrong?


You are right lord slash. You oase to adjust ns frequency kommen sie your city. Weil das example if you are living an the german city bremen the appropriate frequency is: 578000000 Hz

Channel 45 example: 666 MHzChannel width: 8 MHzRight channel zum Bremen: 3445-34 = 11666 MHz - (11*8 MHz) = 578 MHz = 578000000 Hz

You can find ns right channel here: http://www.dvb-t2hd.de/files/Senderstandorte_Erste_Stufe_DVB-T2_HD.pdf

If freundin don"t want zu calculate, you tun können find die right frequency here: http://www.dehnmedia.de/?page=dvbt2&subpage=demokanal

A big belästigung of DVB-T2 is, that ns video codec ist different. It"s called HEVC (H.265). Ich couldn"t play a DVB-T2 stream through my MacBook Pro und VLC. Die CPU fill was auch high.

My setup:*OS: Ubuntu Server 16.04 amd64 (I added ns right firmware kommen sie /lib/firmware)*DVB-T2 USB Stick: TechnoTrend TT-TVStick CT2-4400 (Silicon Labs Si2168)*HTS webocalendar.com 4.0.9-13~g64fec81~xenial